Whereas I want we may belief everybody on the market, we don’t reside in an ideal world the place theft isn’t a factor. I typically make lengthy street journeys solo for my fishing journeys and sticking all my rods inside my truck cab at each cease I make is a ache within the ass. So I’m going to indicate you tips on how to preserve your rods from rising legs and strolling off if you are within the lavatory or grabbing a fast chew to eat with this DIY mattress rack or roof rack mounted fishing rod tube. Constructing considered one of these your self will prevent an honest chunk of change in comparison with simply shopping for a premade one on-line.
DIY Articles on OutdoorHub
Okay, the very first thing that you must do is seize some pipe. I discovered 10-foot lengths of 6″ PVC pipe at Lowes regionally for round $65 a bit, so not likely low cost however one of many solely massive buys you want for this venture. For those who don’t suppose that you must go that massive you will get a 4″ PVC Pipe or in the event you suppose you want a bit bigger you’ll be able to go along with an 8″ PVC pipe. For reference, I can match a St. Croix Mojo Bass with a Shimano Stradic 2500 reel into the 6″ PVC pipe snuggly.
The following factor that you must get a “conduit service equipment” on-line. I acquired mine from Amazon for below $60 bucks for the equipment. These are additionally obtainable in different sizes however the associated fee adjustments as you go up or down in measurement. They’re all fairly related, an finish cap, a door, and brackets to mount it to your mattress or roof rack. These are the 2 massive buys for the fishing rod tube.
Different issues you will have to get for the roof or mattress rack mounted Fishing Rod Tube, are 2 cans of Krylon Fusion paint, 1 tube of silicone, and 6 stainless self-tapping screws. Now you bought every little thing you want the very first thing that you must do is scuff up the floor of the PVC pipe with sandpaper or a sanding block. That is for higher paint adhesion later. After that’s executed give the PVC pipe a wash to do away with all of the mud and grime. That is the perfect time to additionally minimize down the PVC pipe to the size you need your fishing rod tube to be. I fish plenty of 9ft lengthy one-piece rods from the pier so I minimize mine to 9 foot 2 inches. I additionally minimize mine after I painted however I don’t advocate that. I wasn’t certain if I needed to go along with a full 10′ or not at this level and determined the trim was for the higher.
Then degrease the pipe with some alcohol. After that’s executed the pipe is prepared for portray, decide no matter colour you want. Or simply sand off the PVC markings and name it a day with the white of the pipe and skip these subsequent steps.
Arrange your pipe on no matter portray stand you may have, I used some scrap wooden to make mine. Then comply with the instructions on the can and paint a few coats of paint. Let this treatment in a single day after you get the coats on the paint for the toughest end. You can even use clearcoat if you wish to assist shield the end, I didn’t as a result of I used to be in a rush however I even have a number of scuffs the place I scratched off the paint too.
As soon as your PVC pipe is minimize to size and the paint is ready on it, it’s time to connect the tip caps of the conduit equipment to it. First, put a bead of silicone or adhesive of your selection across the lip of the caps. This has two functions, one to stick the caps on and two as weatherproofing to maintain the rain out of your fishing rod tube. After you get bead on the caps firmly stick them onto the PVC pipe. Then take your self-tapping screws and stick 3 of them in every cap to actually lock the caps onto the pipe. That is the tip of the constructing portion, the remainder is simply mounting.
Now get the offered mounting {hardware} and determine the place you need the fishing rod tube to take a seat. I mounted mine on an affordable Harbor Freight Aluminum Mattress Rack so I wanted to drill some holes to mount it in place.
Place the fishing rod tube so it doesn’t stick out too far out the again of your car, for my truck I’ve it protruding so far as the tailgate could be when its open. After getting the holes drilled or the mounting level picked simply set your fishing rod tube on the mount and lock down the offered U-Bolt and nuts. Throw a lock on it, no level in having safe storage and not using a lock to maintain it safe. Then you definately’re executed, able to go. No extra having to fret about somebody snatching your rod when you run to the lavatory at that pit cease in the midst of nowhere in your option to fish.
One final notice, both grease or repaint the U-Bolts which can be offered after you assemble every little thing. A whole lot of kits aren’t utilizing stainless bolts so salt publicity eats them up.
